ASA 5505 with Security Plus license support LAN-Based failover (Active/Standby)
you need
- two ASA 5505 with Security Plus license
- one crossover cable
In our configuration we use
- ethernet 0/5 for failover link
- ethernet 0/1 for internal lan
- ethernet 0/3 for outside internet
configure primary ASA
ciscoasa# conf t
ciscoasa(config)# hostname ASA5505-1
ASA5505-1(config)# interface vlan 221
ASA5505-1(config-if)# description LAN Failover
ASA5505-1(config-if)# no shutdown
ASA5505-1(config)# failover
ASA5505-1(config)# failover lan unit primary
ASA5505-1(config)# failover lan interface failover Vlan221
ASA5505-1(config)# failover interface ip failover 10.221.10.1 255.255.255.0 standby 10.221.10.2
SA5505-1(config)# int Vlan 80
ASA5505-1(config-if)# ip address 10.80.10.1 255.255.255.0 standby 10.80.10.2
ASA5505-1(config-if)# nameif TDMZ
ASA5505-1(config-if)# no shutdown
ASA5505-1(config)# int vlan 99
ASA5505-1(config-if)# ip address 10.10.20.253 255.255.255.0 standby 10.10.20.254
ASA5505-1(config-if)# nameif Outside
ASA5505-1(config-if)# security-level 100
ASA5505-1(config-if)# no shutdown
ASA5505-1(config)# interface ethernet 0/3
ASA5505-1(config-if)# switchport access vlan 99
ASA5505-1(config-if)# description Outside
ASA5505-1(config-if)# no shutdown
ASA5505-1(config-if)# interface ethernet 0/1
ASA5505-1(config-if)# description TDMZ
ASA5505-1(config-if)# switchport access vlan 80
ASA5505-1(config-if)# no shutdown
ASA5505-1(config-if)# interface ethernet 0/5
ASA5505-1(config-if)# description Failover
ASA5505-1(config-if)# switchport access vlan 221
ASA5505-1(config-if)# no shutdown
ASA5505-1# write memory
configure secoundary ASA
ciscoasa(config)# hostname ASA5505-2
ASA5505-2(config)# int vlan 221
ASA5505-2(config-if)# description LAN Failover
ASA5505-2(config-if)# no shutdown
ASA5505-2(config-if)# failover
ASA5505-2(config)# failover lan unit secondary
ASA5505-2(config)# failover lan interface failover Vlan221
ASA5505-2(config)# failover interface ip failover 10.221.10.1 255.255.255.0 standby 10.221.10.2
ASA5505-2(config)# interface ethernet 0/5
ASA5505-2(config-if)# description Failover
ASA5505-2(config-if)# switchport access vlan 221
ASA5505-2(config-if)# no shutdown
ASA5505-2(config-if)# write memory
after failover up secondary ASA get config from primary and rename hostname to ASA5505-1
check failover
ASA5505-1# show failover
Failover On
Failover unit Primary
Failover LAN Interface: failover Vlan221 (up)
Unit Poll frequency 1 seconds, holdtime 15 seconds
Interface Poll frequency 5 seconds, holdtime 25 seconds
Interface Policy 1
Monitored Interfaces 3 of 23 maximum
Version: Ours 8.4(3), Mate 8.4(3)
Last Failover at: 18:52:25 UTC Jan 24 2012
This host: Primary - Active
Active time: 1022 (sec)
slot 0: ASA5505 hw/sw rev (1.0/8.4(3)) status (Up Sys)
Interface TDMZ (10.80.10.1): Normal (Monitored)
Interface Outside (10.10.20.253): Normal (Monitored)
slot 1: empty
Other host: Secondary - Standby Ready
Active time: 0 (sec)
slot 0: ASA5505 hw/sw rev (1.0/8.4(3)) status (Up Sys)
Interface TDMZ (10.80.10.2): Normal (Monitored)
Interface Outside (10.10.20.254): Normal (Monitored)
slot 1: empty
2 comments:
Thanks for the post!! It saved a lot of time on LAN based failover on 5505 series
This post was so easy to follow, much better than what Cisco provides. Thank you!
Post a Comment